Audi Q5 Forum banner
1 - 4 of 4 Posts

· Registered
Joined
·
3 Posts
Discussion Starter · #1 ·
Hi All,

In one last ditch attempt to rectify issues with my newly installed OEM rear view camera into my 2018 Audi Q5 before taking it to the dealers, I thought I would post my issue and installation process to see if any super brains out there can guide me.

Hardware Installation (As directed by VAGtec.co.Uk):

Red - Fused in no. C 13 in rear luggage compartment
Brown - Earthed in same compartment
Black - MMI Quadlock blue - Pin 12
White - MMI Quadlock blue - Pin 6
Orange/Brown - Low CAN - Black connector under rear bench - Pin 30
Orange/Violet- High CAN - Black connector under rear bench - Pin 12

Coding (Using OBDeleven pro):

1/ Gateway (19) - installation of camera
2/ Media (5F) - Adaption - BAP Generation 2 - VPS 0x08 (Active) & Comfort Data Bus
3/ Rear View Camera (6C) - Long Coding - Rear View Modes 1,2&3 Enabled

Note: Although I have parking sensors, I do not have a ‘Parking Assistant’ module option.

Problem:
Once I had disconnected OBDeleven the rear view camera worked when put into reverse. It also worked when pressing the park assist button , however it then just stopped!

I now have the following fault codes and the rear view camera module won’t connect at all.

Gateway - Rear view camera module no communication- U104C00

Gateway - Databus - Additional installation detected - U112400

Multimedia - Function limitation due to missing message - U11110

Thank you for reading. Any assistance would be greatly appreciated.

Regards,

Adam
 

· Registered
Audi SQ5 2015
Joined
·
2,287 Posts
No experience of doing this mod, but have you tried contacting VAGtec yet for advice? I would maybe check all the connections again. Maybe check the coding is correct. Is the 'Parking Assistant' a requirement for the rear view camera according to VAGtec? Strange that it working initially then just stopped! :unsure:
 

· Registered
2014 Audi Q5 8R SE 3.0 tdi
Joined
·
253 Posts
Putting the search "audi fault code #####" those given above, in Google gives some idea of the problems. First seems to be rear xamera module is now non functional. Fuse, or module blown? Good luck!
 

· Registered
Joined
·
11 Posts
Hi All,

In one last ditch attempt to rectify issues with my newly installed OEM rear view camera into my 2018 Audi Q5 before taking it to the dealers, I thought I would post my issue and installation process to see if any super brains out there can guide me.

Hardware Installation (As directed by VAGtec.co.Uk):

Red - Fused in no. C 13 in rear luggage compartment
Brown - Earthed in same compartment
Black - MMI Quadlock blue - Pin 12
White - MMI Quadlock blue - Pin 6
Orange/Brown - Low CAN - Black connector under rear bench - Pin 30
Orange/Violet- High CAN - Black connector under rear bench - Pin 12

Coding (Using OBDeleven pro):

1/ Gateway (19) - installation of camera
2/ Media (5F) - Adaption - BAP Generation 2 - VPS 0x08 (Active) & Comfort Data Bus
3/ Rear View Camera (6C) - Long Coding - Rear View Modes 1,2&3 Enabled

Note: Although I have parking sensors, I do not have a ‘Parking Assistant’ module option.

Problem:
Once I had disconnected OBDeleven the rear view camera worked when put into reverse. It also worked when pressing the park assist button , however it then just stopped!

I now have the following fault codes and the rear view camera module won’t connect at all.

Gateway - Rear view camera module no communication- U104C00

Gateway - Databus - Additional installation detected - U112400

Multimedia - Function limitation due to missing message - U11110

Thank you for reading. Any assistance would be greatly appreciated.

Regards,

Adam
Have you scanned with Full VCDS yet to see if there is anything your initial scan missed.
 
1 - 4 of 4 Posts
Top